Thursday, July 1, 2010

Shirr without fear!!!

My sewing friends fall into two categories...shirrers and non-shirrers. Some folks can plop elastic thread in the bobbin, set the machine to the right settings, and voila...perfect shirring. Other very talented people can't shirr to save their life. It isn't their fault, their machine just won't let them shirr. I fall somewhere in between. I've successfully shirred in the past, but I've also had some awful, inconsistent messes. Even though I love the look of shirring (and it so wonderfully forgiving in the size category), I avoid using it in any of my designs. Well, my neighbor made a cute sundress out of a pre-shirred fabric from Jo-Ann, and I loved the look and knew I had to have one out of Sis Boom fabric for a picnic this weekend. So I've been practicing, and I think I've come up with a technique that should work for everyone, no matter how sadistic their sewing machine.


Photobucket

The first step is winding the elastic thread onto bobbin. Most shirring methods recommend winding the bobbin by hand. I'm just not that patient or focused when it comes to those kinds of things. I decided to wind mine by machine - it gets much more of the thread on the bobbin, and takes only seconds as opposed to minutes (yeah, that is lavender thread on my bobbin beneath the elastic thread...I couldn't find an empty, and was too lazy to unwind).

OK, as long as we are at the machine, let's talk settings. I used the longest straight stitch length, and set the bobbin tension just a bit higher than the lowest setting (1 on my machine). I set the needle position all the way over to the far left.


Photobucket

For my test scrap, I used a 16 inch wide piece of Tanya from the Sis Boom Poodle line. Jennifer really outdid herself this time!! I love every print and every colorway in this collection, but there is something just so Euro-fun about this particular paisley. I finished the top edge with the serger, but on my sundress I'm going to do a hem.

Photobucket

On to the shirring! Start the first line of shirring the desired distance away from the top, prefinished edge of the fabric. Make sure the right side of the fabric is facing up. Before stitching, BACKSTITCH...this is very important.


Photobucket

Start stitching. Don't worry about what is feeding out of your machine at this point. It might be tightly gathered, loosely gathered...doesn't matter. Just focus on keeping the stitching nice and straight.


Photobucket

When you get to the end of the fabric, grasp the end of the stitching and pull the piece away from the machine so that you leave a nice long tail at the end of the stitching (at least 6 inches stretched). Snip.


Photobucket

This is what my piece looked like after the first row of shirring. Your piece may look tighter or looser, but but like I said it doesn't matter because...


Photobucket

...you are just going to take out the gathers anyway! Working away from the backstitched end, push the gathers out towards the tail.


Photobucket

You won't be able to get it perfectly flat, but it will be pretty close to the original length.


Photobucket

Onto the second row! With the right side facing up, position the right edge of the presser foot against the first line of stitching. BACKSTITCH, then stitch the line of shirring. Since you ungathered the first row, you shouldn't have any problems with puckers. Pull out a long tail at the end and snip.

Photobucket

Straighten out row two so it is just like row one.


Photobucket

Repeat this process as many times as needed. I did 6 rows of stitching for my test, which gave about a 2" band of shirring. The next step is to pull on the tails to shorten the elastic for that stretchy gathered effect.


Photobucket

The next step is to pull on the tails to shorten the elastic for that stretchy gathered effect. You want the gathering to be consistent, so you will need to mark the strands with a washable marker. Decide how much you want to shorten up the strands of elastic (keep in mind they will shrink even more than this amount after steaming, but they will still have lots of give). Lay out the shirred piece with the elastic side facing up. Measure out the desired distance away from the tail end. I measured out 8" with the intention of the finished shirred band being at least 50% shorter than the original length. Since shirring is sooooo stretchy, I think it is better to get it a bit on the tight side than on the loose side.

Photobucket

Pull each of the tails individually until the marked position is at the side edge of the fabric.


Photobucket

Tie the elastic and the corresponding needle thread into a knot at the position of the mark. Don't worry if you don't hit it exactly.


Photobucket

Once you have tied off all of the threads, work the shirring between your fingers to evenly distribute the gathers.


Photobucket

It will look pretty good, but not perfect. Here comes the fun part...set your iron to a hot, steamy setting, and blast the shirring with steam for a few seconds.


Photobucket

I didn't get pics of the actual process because the steam fogged up my lens, but the shirring magically shrinks up into a smocking-pleat perfect delight!


Photobucket

Fully stretched, my final shirred band is about 8" - 50% shorter than the original length.


Photobucket

Unstretched, it is 4" - 75% shorter than the original length! I've never been able to get such nice, tight shirring before, and I'm looking forward to playing with the amount of gathering for different effects. Now that I have control of my shirring, I need to do some math and plan my sundress!